115v ac 1/8 hp pmdc electric motor variable speed drive reversible
1/8 hp Reversible 115V AC PM Motor Variable Speed Drive

This product is now replaced by a new version.  Please click [HERE].

This is a compact PMDC (Permanent Magnet Direct Current) electric motor with a variable speed
controller that takes a regular 115VAC input from a regular appliance outlet.  Due to properties of
permanent magnet stator, this motor is able to generate great torque at low speed.  

Controller:  On/Off switch, variable speed knob, reverse/forward switch, 115vac power cord in length of
54 inches(1372mm)

Motor:  No load@5837RPM; 75W@0.17N-m(1.6 in-lb)@4000RPM; 101W@0.377N-m(3.4
in-lb)@2566RPM.  Basically, the lower the speed, the higher torque it's going to output.  A torque curve
can be plotted by simply using the 3 data points provided.  Shaft is 10mm in diameter with flat and 32mm
in length.  Square flange is measured to be 80mm by 80mm.  Diameter of mounting hole pattern is
93.5mm wide.  Each mounting hole is measured to be 5.5mm in diameter.  Distance from the front face
of square flange to the back of motor is 111mm.  Cylindrical portion of the motor has a diameter of
78mm and an axial length of 104mm.

Connection between motor and controller is 20 inch(508mm) long.

Manufacturer:  Wondermotor (wondermotor.com)

To wholesale or OEM buyers:  we can build a motor based on your specifications for your high-quantity
demand.
115v / 230v ac variable speed reversible brushless gear motor
115v 230v ac Gearmotor Reversible  Variable Speed Drive
This is a compact, single-phase, 115v ac to 230v ac input,  permanent magnet, brushless gear motor
with reversible, on/off, speed adjustable controls. Speed range varies depending on the shaft load.
Motor's maximum speed is 38 RPM. Rotation is reversible by a signal wire.  This combination will be
described in two parts: brushless dc gear motor and power adapter.

Brushless DC Gear Motor:  8.4 N-m (6.2 ft-lb) torque at 35 RPM.  Permanent magnet rotor.  60mm x
60mm square front.  4 M5 threaded holes located at front for face mounting.  Motor length is 6.5 inch
(165mm) long and its controller is integrated as part of the motor.  Shaft is 8mm in diameter with a flat
and is 1 inch (25.4mm) long.  The control line, which contains speed adjustment (with a pot soldered
already), reversing signal wire, on/off signal wire, and signal ground wire, is 20 inch (508mm) long.  
Connector line that is to connect to the power adapter is 20 inch (508mm) long.  Motor control is very
simple.  To turn the motor on, simply connect the on/off (blue) wire to signal ground (black) wire.  A
typical practice is to introduce a switch between the on/off wire and the ground wire, but one may decide
to solder the on/off (blue) wire to the ground (black) wire if on/off feature is not necessary.  To reverse the
rotation of the motor, simply connect the reverse (white) wire to the same ground wire and the motor will
reverse its rotation.  PLEASE BE SURE THAT THE MOTOR IS AT FULL STOP BEFORE REVERSING.
To vary the speed, simply turn the potentiometer.

Power Adapter:  The power cord is 5 ft(152 cm) long and has a standard plug ready to plug into a
standard appliance outlet.  The adapter is able to universally accept 115v ac or 230v ac.  Connector line
that is to connect to the motor is 3 ft (91 cm) long.  Adapter's dimensions are 2.5 in(64mm) width by
4.75in(121mm) length by 1.75in(44mm) depth.  

Manufacturer:  Wondermotor (wondermotor.com); UME (umemfg.com)

To wholesale or OEM buyers:  we can build a motor based on your specifications for your high-quantity
demand.
115V 60HZ Electric Motor 80W Variable Speed CW 115vac

This product is now replaced by a new version.  Please click [HERE].

This is a compact, single-phase, 80W, 60HZ, 115VAC induction motor with a speed-control box.  Speed
range varies depending on the shaft load.  Motor's speed at no load is 1760 RPM.  Rotation is
Clockwise when viewing from the shaft end.  The controller has a standard power cord so user can run
the motor right away right out of box.  This motor is 75mm(3") in diameter and 92mm(3.6") in axial length
less shaft.  Connected overall cable length between the controller and the motor is 356mm(14"), and the
power cord length is 1270mm(50").  The motor features 4 bolt holes for a front-mount installation.  The
diameter of the bolt-hole pattern is 55mm(2.2").  Shaft is 8mm(0.31") in diameter and 19mm(0.75") long
with a flat (D shaft).  Ideal for home projects/experiments.
12v / 24v Gear Motor PWM Variable Speed 12vdc Gearmotor CCW

This product is now replaced by a new version.  Please click [HERE].

This is a brand new electric gear motor that has an extremely high torque and is speed adjustable with
a PWM (Pulse Width Modulating) controller.  The gear motor is measured to be 7 inch long and the
motor itself has a diameter of 2.5 inches.  Drive shaft is 10mm in diameter with 2 flats where flat to flat is
6mm.  The shaft has a threaded end that is to fit a M6 tightening nut.  Rated voltage of this gear motor is
13.5 VDC and maximum speed is 50 RPM.  Rated output load is 60 watts and output toruqe at 50 RPM
is 11.5 N-m (8.5 ft-lb).  Mounting is based on M6 screw mounting.  The PWM controller features
controller-off wires so when the two (blue) wires are in contact, the controller is instantly disabled.  This
feature is offered as an option and the user may decide not to use it.  A 10k ohm potentiometer is
provided and is wired to the controller.  Red wire is to positive and black is to negative.  The controller
does not accept reverse polarity and doing so will permanently damage the controller.  Shaft rotation is
CCW.  Manufacturer:  Wondermotor (wondermotor.com)
PWM CONTROLLER GEAR MOTOR 12V
12v Gear Motor PWM Variable Speed 12vdc Gearmotor
This is a brand new electric gear motor that has an extremely high torque and is speed adjustable with
a PWM (Pulse Width Modulating) controller.  The gear motor is measured to be 7 inch long and the
motor itself has a diameter of 2.5 inches.  Drive shaft is 10mm in diameter with 2 flats where flat to flat is
6mm.  The shaft has a threaded end that is to fit a M6 tightening nut.  Rated voltage of this gear motor is
13.5 VDC and maximum speed is 50 RPM.  Rated output load is 60 watts and output toruqe at 50 RPM
is 11.5 N-m (8.5 ft-lb).  Mounting is based on M6 screw mounting.  The 12V DC PWM controller features
a 4 ft(1.2m) long connection to its potentiometer.  The potentiometer has a on/off switch built-in with a
knob.  An overload protection is set at 6 amps of current so the controller will shut down when such a
current occurs.   There are connectors between the gear motor and the controller.  To run the gear motor
in CW rotation, please connect motor's green connector to controller's red connector and motor's red
connector to controller's black connector.  To run the gear motor in CCW rotation, please connect
motor's green connector to controller's black connector and motor's red connector to controller's red
connector.  The distance of the connection wires between the motor and the controller is 1 ft(30cm).  The
distance of the 12v connection wire is 10 in(25cm) long.  

Manufacturer:  Wondermotor (wondermotor.com)
Wireless Remote Control 12v dc gear motor
12v dc gear motor with wireless remote control

This is a brand new electric gear motor that has an extremely high torque and is equipped with a
wireless controller.

The gear motor is measured to be 7 inch long and the motor itself has a diameter of 2.5 inches.  Drive
shaft is 10mm in diameter with 2 flats where flat to flat is 6mm.  The shaft has a threaded end that is to
fit a M6 tightening nut.  Rated voltage of this gear motor is 13.5 VDC and maximum speed is 50 RPM.  
Rated output load is 60 watts and output toruqe at 50 RPM is 11.5 N-m (8.5 ft-lb).  Mounting is based on
M6 screw mounting.

ON/OFF Switch Option:  The wireless controller functions as a on/off switch on the 12v dc power source.  
By pressing the button "on" once, the motor starts running continuously; by pressing the button "off"
once, the motor stops running. Current rating is 15 amps.  Two transmitters (with batteries) are included
in this package.  Wireless signal range is 100 ft.

Momentary Switch Option:  The wireless controller functions as a reversible momentary control switch
from a 12v dc power source. By holding down the right side button, the motor runs in one direction until
the user releases the button; by holding down the left side button, the motor runs in the opposite
direction until the user releases the button. Current rating is 3 amps.  Two transmitters (with batteries)
are included in this package.  Wireless signal range is 100 ft.

Latch Switch Option:  The wireless controller functions as a reversible latch control switch from a 12v dc
power source.  By pressing the right side button once, the motor runs in one direction continuously, by
pressing the right side button once again, the motor stops; by pressing the left side button once, the
motor runs in the opposite direction continuously, by pressing the left side button once again, the motor
stops. Current rating is 3 amps.  Two transmitters (with batteries) are included in this package.  
Wireless signal range is 100 ft.

This is a single speed system.

Manufacturer:  Wondermotor (wondermotor.com)
Brushless 115V AC 1/8 hp ECM Electric Motor Variable Speed Drive Reversible

This product is now replaced by a new version.  Please click [HERE].

This is a compact Electronically Commutated Motor with a variable speed control panel that displays the
speed of the motor.  The motor takes a regular 115VAC input from a regular appliance outlet.  Due to
properties of its permanent magnet rotor, thismotor is able to generate great torque at low speed.  

Controller:  On/Off switch, variable speed knob, CW/CCW switch, RPM display, 115vac power cord in
length of 54 inches(1372mm)

Motor:  No load@5500RPM; 75W@0.17N-m(1.6 in-lb)@4000RPM; 100W@0.377N-m(3.4
in-lb)@2500RPM. A torque curve can be plotted by simply using the 3 data points provided.  Shaft is
8mm in diameter with flat and 77.5mm in length.  Face mount design with 2 threaded Metric holes at
front.  Diameter of mounting hole pattern is 72.6mm wide.  Cylindrical portion of the motor has a
diameter of 85mm and an axial length of 91mm.

Connection between motor and the control panel is 12 inch(305mm) long.

Manufacturer:  Wondermotor (wondermotor.com)

To wholesale or OEM buyers:  we can build your motor based on your specifications for your
high-quantity demand.
WONDERMOTOR
YOUR SOURCE OF HIGH QUALITY MOTORS
[ E-mail:  sales@wondermotor.com ] [ Phone:  626.322.9220 ]
[ Discussion Home Page ]      |      [ Product Home Page ]
Our products are available to be purchased online.  Please simply click on the product(s) that you wish to
order below for more information.  For products that are listed here but not found in our online store, simply
e-mail or call us to request for your order(s).  We also welcome wholesale/resale buyers.  [ Privacy Policy ]